All Consumables

Clamex S is a knock down connector that is screwed into an 8 mm groove and connected via a lever. The 8 mm groove cutter for Clamex S can be used w...

Clamex P Medius complements the Clamex P-14 connectors for use in shelving units where two shelves meet the dividing panel at the same height. Medi...

Lamello 132108 Curbide Cutter for Clamex S Clamex S Carbide Reversing Blades Cutter for 8 mm Groove Cutter Dimensions: 100 x 8 x 22 mm

Tough and strong Systainer 2 case Robust ABS with moulded-in reinforcing ribs Flush fitting top handle, stackable

Lamello 145001 - K20 Self Clamping and Gripping Plates, Pack of 80 Plastic element with lateral clamping ridges for anchoring in the groove Used i...

The biscuit is the original, tried-and-tested connector from the inventor of the system and provider of the complete solution. The success of the b...

This starter set includes: 80 Pairs Divario connectors Installation tool Metal Marking Jig Drill bit & stop collar Systainer

The P-System connecting fittings can be installed either with the Zeta P2 power tool or using a CNC machine. The use on a CNC machine requires the ...

The Lamello preload insertion tool aids in the correct placing of the Tenso pre-load clips into the Tenso connector

The Tenso P-14 is a self-clamping connector with three functions: alignment, clamping and connecting. The very high level of clamping force allows ...

Positioning Clip for Zeta P Used for positioning in the Clamex 6mm Access Hole

Positioning Pins for Zeta P2 For positioning in holes with a diameter of either Ø 5mm or 8mm

Install knobs and handles in seconds with the most accurate jig on the market. Perfect results every time on any cabinet door or drawer front. Incl...

Includes the Rapid Center Extension for rapid drawer front centering and quick repeatable door settings. Install knobs and handles in seconds with ...

Install knobs and handles in seconds with the most accurate cabinet hardware jig on the market. Perfect results every time on any cabinet door or d...

Cabinet Lighting Made Easy For Strip Lights and Puck Lights The Cabinet Light Jig MAX can install both 2-1/4″ & 2-1/8″ puck lights and the ligh...

Cabinet Lighting Made Easy For Strip Lights and Puck Lights The Cabinet Light Jig can install both 2-1/4″ puck lights and the light wire within the...

Cabinet Lighting Made Easy For Strip Lights and Puck Lights The Cabinet Light Jig can install both 2-1/4″ puck lights and the light wire within the...

Cabinet Lighting Made Easy For Strip Lights Simplify cabinet lighting with our revolutionary Cabinet Light Jig! This tool installs the light wire w...

CNC In-Board Gasketing Low Density 1/16” x 1/8” x 164 Ft / Roll Adhesive One Side Available in 18 Roll Cases 15% Savings When Ordered By The Case

CNC In-Board Gasketing Low Density 1/16” x 1/4” x 82 Ft / Roll Adhesive One Side Available in 18 Roll Cases 15% Savings When Ordered By The Case

CNC In-Board Gasketing Low Density 1/16” x 3/8” x 82 Ft / Roll Adhesive One Side Available in 18 Roll Cases 15% Savings When Ordered By The Case

CNC In-Board Gasketing Low Density 1/16” x 1/2” x 164 Ft / Roll Adhesive One Side Available in 18 Roll Cases 15% Savings When Ordered By The Case

CNC In-Board Gasketing Low Density 1/16” x 1” x 164 Ft / Roll Adhesive One Side Available in 18 Roll Cases 15% Savings When Ordered By The Case