EVANS MIDWEST | CS-XL Cutting Station ORMA Hot Presses
Evans Midwest CS XL Signature™ Cutting Station is a high-performance postforming miter saw engineered to accommodate a wide range of kitchen countertop and vanity sizes. The CS XL provides an overall cutting capacity of 53.5 inches (1360 mm) at 90° and 37.5 inches (950 mm) at 45°, with a maximum backsplash height of 4.875 inches (124 mm) measured from the bottom of the deck.
Evans Midwest Cutting Stations are well known for producing fast, accurate miter cuts and drawbolt mortises in postformed countertop fabrication. A single operator can complete a miter joint with integrated drawbolt mortises in under three minutes, reducing handling time, minimizing operator fatigue, and helping prevent product damage.
With more than 50 years of manufacturing experience, Evans Midwest continues to refine its equipment as fabrication technology advances. The CS XL Signature™ Cutting Station is available in both CS XL and XLT configurations, offering proven performance backed by decades of industry expertise.
Standard Features
-
Upper and lower frames machined in a single setup at Evans Midwest’s advanced manufacturing facility
-
Fixed stops at 22.5°, 45°, and 90° (right- and left-hand sides)
-
Pneumatic locking pin
-
5 HP saw motor with heavy-duty arbor assembly
-
Variable speed forward/reverse drive
-
Router system with four (4) router motors, guiding template, and rotating template pin with ball bearing
-
Two (2) pneumatic hold-down clamps per side
-
OSHA-recognized Safety Awareness Barriers
-
Heavy-duty rear fence
-
Three (3) dust collection ports
-
Plexiglass safety shield
-
Ergonomic low-profile control panel with sure-grip operator handles
-
16-inch (406 mm) saw blade and four (4) router bits
-
Safety interlocks and emergency stop
Optional Equipment
-
Standard and heavy-duty roller conveyors
-
Specialty wheel conveyors
-
Custom fences with nip-over stops
-
TigerStop electronic fence with automatic positioning
-
Laser guideline kit
-
Dust manifold
-
Variable miter kit with digital readout
-
Backsplash clamps
-
Support rings for short parts
-
Dust enclosure kit
-
Fifth router motor kit
Evans Midwest Cutting Stations are fabricated, welded, machined, assembled, and tested at the company’s 45,000-square-foot manufacturing facility in Minneapolis, Minnesota, using advanced machining and fabrication technology.
This fully integrated production process—from raw material sourcing through final shipment—ensures consistent quality control and tight manufacturing tolerances.
Precision Construction Details
King Pin & Bearing Assembly:
A large-diameter king pin with precision bearing mounted in a machined pocket provides stability and smooth rotation on the lower frame.
Saw Carriage:
Mounted on turned, ground, and polished rails with bronze bearings for long-term durability and dependable performance.
Arbor Assembly:
Heavy-duty arbor supported by two precision ball bearings housed in a machined cast iron assembly. Each unit is pre-assembled and bench-tested for vibration-free operation.
Lower Frame Weldment:
Top surface machined flat to ±0.005" for smooth, accurate operation.
Rear Fence:
Front edge machined straight to ±0.0025" to maintain precise cutting accuracy.
Mazak CNC Vertical Mill:
Upper and lower frames machined in a single setup to preserve alignment and maintain tight tolerances.
Specifications
Evans Midwest CS-XL Countertop Cutting Station FAQs
What is the CS-XL used for?
Countertop miter cutting and draw-bolt mortising in one operation.
Which countertop types are listed?
Postformed, self-edge, coved and solid-surface countertops.
What blade is supplied?
A 16-inch, 100-tooth carbide-tipped blade.
What is the cutting height?
5-5/8 inches.
What cutting length is listed at 90 degrees?
54 inches.
What cutting length is listed at 45 degrees?
37.5 inches.
How far does the upper frame pivot?
90 degrees to either side of center.
Which fixed miter positions are described?
22.5, 45 and 90 degrees.
How is the saw carriage guided?
Linear bushings run on precision-ground hardened rails.
What drive is provided?
A variable-speed forward/reverse drive and belt-driven saw arbor.
What routing equipment is included?
Four router motors, a guiding template and four 1/2-inch carbide-tipped router bits.
How is the countertop held?
Two adjustable pneumatic hold-down clamps per side.
What dust collection is required?
At least 2,350 CFM through three 4-inch connections.
What protective controls are listed?
Interlocked end guards, a shield and emergency stop.
Where is it manufactured?
The OEM identifies Holland, Michigan.
